| 3201 |
3110-007A : 1994 (Revision No.1)(Reaffirmed 2013)
|
TECHNICAL SUPPLY CONDITIONS FOR ROLLING BEARINGS |
| 3202 |
Misc 0511A : 2013 (Revision No.2)
|
GREY IRON CASTINGS - SPECIFICATION |
| 3203 |
2540 - 016A : 1988 (RA 2013)
|
DIMENSIONS OF END FITTINGS OF REAR SHOCK ABSORBERS FOR SCOOTERS AND MOTOR CYCLES |
| 3204 |
2815 - 009A : 1987 (RA 2013)
|
METHODS OF TESTS FOR INTERNAL COMBUSTION ENGINES PART IX ENDURANCE TESTS |
| 3205 |
Misc 0841A : 2000 (RA 2013)
|
METHODS OF TESTS FOR INTERNAL COMBUSTION ENGINES PART III MEASUREMENTS FOR TESTING - UNITS AND LIMITS OF ACCURACY |
| 3206 |
7210 - 049A : 2011(Rev No.1) Amdt No.3
|
COTTON MOSQUITO NETTING, ROUND MESH |
| 3207 |
8305 - 048A : 2011(Rev No.1) Amdt No.3
|
COTTON MOSQUITO NETTING, SQUARE MESH |
| 3208 |
8440 - 005A : 1992(RA 2012) Amdt No.2
|
SOCKS, COTTON |
| 3209 |
Misc 1010A : 2008(RA 2013)
|
AUTOMOTIVE VEHICLES - TYPES - TERMINOLOGY PART 1 THREE AND FOUR WHEELERS |
| 3210 |
Misc 1009A : 2008(RA 2013)
|
AUTOMOTIVE VEHICLES - EXTERIOR PROCTECTION FOR PASSENGER CAR - PERFORMANCE REQUIREMENTS |
| 3211 |
Misc 1008A : 2008(RA 2013)
|
AUTOMOTIVE VEHICLES -WHEEL GUARDS FOR PASSENGER CARS - PERFORMANCE REQUIREMENTS |
| 3212 |
Misc 1007A : 2008(RA 2013)
|
AUTOMOTIVE VEHICLES -WHEEL FASTENERS AND HUB CAPS - GENERAL REQUIREMENTS |
| 3213 |
Misc 1006A : 2008(RA 2013)
|
AUTOMOTIVE VEHICLE - REFERENCE VOLUME - LUGGAGE COMPARTMENT OF PASSENGER CARS - METHOD OF MEASUREMENT |
| 3214 |
Misc 1005A : 2013(Rev No.1)
|
PROCEDURE FOR DETERMINING THE 'H' POINT AND THE TORSO ANGLE FOR 50th PERCENTILE ADULT MALE IN SEATING POSITIONS OF MOTOR VEHICLES |
| 3215 |
Misc 1004A : 2008(RA 2013)
|
AUTOMOTIVE VEHICLES - GARAGE EQUIPMENTS TECHNICAL PARAMETERS |
| 3216 |
Misc 1003A : 2008(withdrawn 2013)
|
RECOMMENDATION FOR SAFETY REQUIREMENTS FOR REFLECTING SURFACES OF AUTOMOTIVE VEHICLES |
| 3217 |
Misc 1002A : 2008(RA 2013)
|
LATERAL SPACING FOR FOOT CONTROLS FOR PASSENGER CARS |
| 3218 |
Misc 1011A : 2013 (RA 2013)
|
AUTOMOTIVE VEHICLES - FLAMMABILITY REQUIREMENTS |
| 3219 |
Misc 1012A : 2013 (RA 2013)
|
AUTOMOTIVE VEHICLES - SAFETY BELT ANCHORAGES - SPECIFICATION |
| 3220 |
Misc 1013A : 2013 (Rev No.1)
|
AUTOMOTIVE VEHICLES - SAFETY BELT ASSEMBLY- SPECIFICATION |
| 3221 |
Misc 1014A : 2013 (Rev No.1)
|
AUTOMOTIVE VEHICLES - INTERIOR FITTINGS - SPECIFICATION |
| 3222 |
Misc 1015A : 2013 (Rev No.1)
|
MOTORCYCLES - MEASUREMENT OF MAXIMUM SPEED |
| 3223 |
Misc 1016A : 2013 (Rev No.1)
|
AUTOMOTIVE VEHICLES - TWO WHEELERS ACCELERATION PERFORMANCE - METHOD OF MEASUREMENT |
| 3224 |
2540 - 031A : 2008 (RA 2013)
|
AUTOMOTIVE VEHICLES - REAR VIEW MIRRORS - SPECIFICATION |
| 3225 |
2540 - 032A : 2013 (Rev No.1)
|
SAFETY GLASS - SPECIFICATION PART 2 FOR ROAD TRANSPORT |
| 3226 |
4910 - 004A : 2008 (RA 2013)
|
AUTOMOTIVE VEHICLES - PORTABLE JACKS FOR AUTOMOBILES PART 1 MECHANICAL JACKS - SPECIFICATION |
| 3227 |
4910 - 005A : 2008 (RA 2013)
|
AUTOMOTIVE VEHICLES - PORTABLE JACKS FOR AUTOMOBILES PART 2 HYDRAULIC JACKS - SPECIFICATION |
| 3228 |
Misc 0839A : 2000 (RA 2013)
|
METHODS OF TESTS FOR INTERNAL COMBUSTION ENGINES PART 1 GLOSSARY OF TERMS RELATING TO TEST METHODS |
| 3229 |
Misc 0840A : 2000 (RA 2013)
|
METHODS OF TESTS FOR INTERNAL COMBUSTION ENGINES PART 2 STANDARD REFERENCE CONDITIONS |
| 3230 |
Misc 0538A : 2013 (Rev No.2))
|
ANTIFREEZE COOLANT - SPECIFICATION |
| 3231 |
9150 - 006A : 2000 (Rev No.1) (RA 2013)
|
GENERAL PURPOSE GREASE FOR DEFENCE APPLICATION - SPECIFICATION |
| 3232 |
2805 - 016A : 1993 (RA 2013)
|
INTERNAL COMBUSTION ENGINES - CYLINDER LINERS - QUALITY CHARACTERISTICS |
| 3233 |
Misc 0065A : 1993 (RA 2013)
|
INTERNAL COMBUSTION ENGINES - SETTING IGNITION TIMING IN SPARK IGNITION ENGINES - CODE OF PRACTICE |
| 3234 |
Misc 0064A : 1993 (RA 2013)
|
INTERNAL COMBUSTION ENGINES - METHOD OF TEST FOR PRESSURE CHARGED ENGINES |
| 3235 |
2610 - 008A : 1988 (RA 2013)
|
RECOMMENDATIONS FOR STORAGE AND HANDLING OF PNEUMATIC TYRES FOR AUTOMOTIVE VEHICLES |
| 3236 |
2610 - 007A : 1988 (RA 2013)
|
RECOMMENDATIONS FOR STORAGE AND HANDLING OF INNER TUBES, TUBE VALVES AND FLAPS FOR USE WITH PNEUMATIC TYRES FOR AUTOMOTIVE VEHICLES |
| 3237 |
2815 - 012A : 1987 (RA 2013)
|
METHODS OF TESTS FOR INTERNAL COMBUSTION ENGINES PART XII SPECIMEN TEST CERTIFICATES |
| 3238 |
2815 - 011A : 1987 (RA 2013)
|
METHODS OF TESTS FOR INTERNAL COMBUSTION ENGINES PART XI INFORMATION TO BE SUPPLIED BY THE PURCHASER TO THE MANUFACTURER AND INFORMATION TO BE SUPPLIED BY THE MANUFACTURER ALONGWITH THE ENGINE |
| 3239 |
2815 - 010A : 1987 (RA 2013)
|
METHODS OF TESTS FOR INTERNAL COMBUSTION ENGINES PART X TESTS FOR SMOKE LEVELS, LIMITS AND CORRECTIONS FOR SMOKE LEVELS FOR VARIABLE SPEED COMPRESSION IGNITION ENGINES |
| 3240 |
Misc 0842A : 2000 (RA 2013)
|
METHODS OF TESTS FOR INTERNAL COMBUSTION ENGINES PART IV DECLARATION OF POWER , EFFICIENCY, FUEL CONSUMPTION AND LUBRICATING OIL CONSUMPTION |
| 3241 |
Misc 1001A : 2008(RA 2013)
|
ROAD VEHICLES - FRONTAL FIXED BARRIER COLLISION TEST METHOD |
| 3242 |
Misc 1000A : 2013(Rev No.1)
|
AUTOMOTIVE VEHICLES - BRAKES AND BRAKING SYSTEMS PART 2 GENERAL FUNCTIONS AND FEATURES |
| 3243 |
Misc 0999A : 2008(RA 2013)
|
METHOD OF DETERMINATION OF CENTER OF GRAVITY OF AUTOMOTIVE VEHICLES |
| 3244 |
0450 - 014A : 1994(RA 2013)
|
TITLE OF IS : METHOD FOR QUANTITATIVE CHEMICAL ANALYSIS OF BINARY MIXTURES OF REGENERATED CELLULOSE FIBRES AND COTTON - PART III : FORMIC ACID-ZINC CHLORIDE |
| 3245 |
8440 - 001A : 1985(RA 2013)
|
TITLE OF IS : GLOVES, WOOL, KNITTED O.G. |
| 3246 |
8305 - 025A : 2013(Rev No.1)
|
TITLE OF IS : DYED COTTON FABRIC WATER REPELLANT FOR CAPES AND RAIN COATS |
| 3247 |
8305 - 012A : 2013(Rev No.1)
|
TITLE OF IS : TEXTILE - HEAVY CEE JUTE CLOTH |
| 3248 |
Misc-915A : 2013 (Rev No.1)
|
STEEL - DETERMINATION OF CONTENT OF NON METALLIC INCLUSIONS MICROGRAPHIC METHOD USING STANDARD DIAGRAMS |
| 3249 |
Misc-913A : 2007 (Rev No.1)(RA 2013)
|
TECHNICAL SUPPLY CONDITIONS FOR THREADED STEEL FASTENERS - PART 2 : TOLERANCES FOR FASTENERS - BOLTS, SCREWS, STUDS AND NUTS - PRODUCT GRADES A, B AND C |
| 3250 |
Misc-914A : 2007 (Rev No.1)(RA 2013)
|
TECHNICAL SUPPLY CONDITIONS FOR THREADED STEEL FASTENERS PART 3: MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL -BOLTS, SCREWS AND STUDS |
