| 501 |
0740 : 2019
|
FORGING OF TITANIUM ALLOYS |
| 502 |
0701 : 2018 (First Revision)
|
DRAWING NUMBERING (EDS-AERO) (ENGINEERING DRAWING STANDARDS-AEROSPACE) |
| 503 |
0695 : 2018 (First Revision)
|
GEOMETRICAL TOLERANCE OF TECHNICAL DRAWINGS (GEOMETRICAL TOLERANCING OF FORM, ORIENTATION, LOCATION AND RUNOUT, SYMBOLS AND INDICATION ON DRAWINGS) (EDS-AERO) (ENGINEERING DRAWING STANDARDS-AEROSPACE) |
| 504 |
0794 : 2014 Reaffirmed 2019
|
W-BAND HIGH GAIN REFLECTOR ANTENNA SYSTEM |
| 505 |
0792 : 2014 Reaffirmed 2019
|
mm WAVE DIPLEXER AT Ka-BAND |
| 506 |
0791 : 2014 Reaffirmed 2019
|
mm WAVE Ka-BAND LOW NOISE AMPLIFIER |
| 507 |
0154 : 2019 (Third Revision)
|
SEALING OF THE INSTRUMENTS |
| 508 |
0737 : 2019
|
SELECTION OF AN INTERNAL COMBUSTION ENGINE FOR PROPULSION OF UNMANNED AIRCRAFT SYSTEM BASED ON ANALYTIC HIERARCHY PROCESS |
| 509 |
0706 : 2019 (First Revision)
|
QUALIFICATION OF IVCONEL 718 PQ FORGED TURBINE DISCS |
| 510 |
0704 : 2018 (First Revision)
|
MANDATORY REQUIREMENTS (EDS-AERO) (ENGINEERING DRAWING STANDARDS-AEROSPACE) |
| 511 |
0703 : 2018 (First Revision)
|
CHANGE LAYOUTS (EDS-AERO) (ENGINEERING DRAWING STANDARDS-AEROSPACE) |
| 512 |
0702 : 2018 (First Revision)
|
CHANGE NOTICE (EDS-AERO) (ENGINEERING DRAWING STANDARDS-AEROSPACE) |
| 513 |
0697 : 2018 (First Revision)
|
IDENTIFIABLE PARTS (EDS-AERO) (ENGINEERING DRAWING STANDARDS-AEROSPACE) |
| 514 |
0696 : 2018 (First Revision)
|
PROJECT SLIPS (EDS-AERO) (ENGINEERING DRAWING STANDARDS-AEROSPACE) |
| 515 |
0693 : 2018 (First Revision)
|
LIMITS, FITS AND TOLERANCE (EDS-AERO) (ENGINEERING DRAWING STANDARDS-AEROSPACE) |
| 516 |
0460-01: 2018 (Sec Rev)
|
Prevention Of Corrosion Of Cadmium And Zinc Plating By Vapours From Organic Materials |
| 517 |
0208 : 2013 Reaffirmed 2019
|
STATEMENT OF TECHNICAL REQUIREMENTS FOR FITMENT OF INERTIAL NAVIGATION SYSTEM (RING LASER GYRO) PROJECT 17A SHIPS (EED-56-09) |
| 518 |
0207 : 2013 Reaffirmed 2019
|
Statement Of Technical Requirements For Fitment Of Transmitting Type Magnetic Compass Project 17A (EED-56-13) |
| 519 |
0206 : 2005 Reaffirmed 2019
|
Commercial Off The Shelf (Cots) Electrical Equipment |
| 520 |
0672 : 2013 (First Revision) Reaffirmed 2019
|
Configuration Control Management |
| 521 |
0739 : 2019
|
Rigid Closed Cell Foam For Structural Applications |
| 522 |
0738 : 2019
|
General Guidelines For Manufacturing Composites Components AutoClave Cured |
| 523 |
0736 : 2019
|
Procedure For Design, Development Of X- Band Passive Monostatic Radar Cross Section (RCS) Enhancement Using Luneburg Lens For Arial Targets |
| 524 |
0735 : 2019
|
Procedure For Design, Development And Qualification Of Omni Directional Airborne Antenna For UHF-Band DataLinks Of Male UAS |
| 525 |
0734 : 2019
|
Procedure For Design, Development And Qualification Of Omni Directional Airborne Antenna For S-Band Telemetry Applications Of Male UAS |
| 526 |
0733 : 2019
|
Procedure For Design, Development And Qualification Of Omni Directional Airborne Antenna For C-Band Data Links Of Male UAS |
| 527 |
0732 : 2019
|
Guidelines For Using Halt And Hass Approach For Screening Of Airborne Active Transmit/Receive Modules |
| 528 |
0731 : 2019
|
Procedure For Modified Condition Decision Coverage (MCDC) Of Avionics Software Source Code |
| 529 |
0700 : 2013 Reaffirmed 2019
|
Qualification Of Forged Steel Alloy Turbine Discs |
| 530 |
0699 : 2013 Reaffirmed 2019
|
Qualification Of Compressor/Fan Discs Made From Z12CND12 Steel Alloy (C - 0.12%, Cr-Ni-Mo-V-12%) |
| 531 |
0128: 2018
|
DGQA Evaluation Of Tank GUN & ALG |
| 532 |
3455 -15 : 2012
|
Cutter Milling Shell End |
| 533 |
0309 : 2019 Second Revision
|
Defect Investigation |
| 534 |
50102 : 2018 (Six Revision)
|
List Of Approved Electronic Components |
| 535 |
0819: 2019
|
W-Band Horn Antenna |
| 536 |
0813 : 2017
|
SiGe Based Ka-Band Low Noise Amplifier (LNA) |
| 537 |
0812 : 2017
|
High Peak Power Generator AT W-Band For Radar Application |
| 538 |
0809 : 2017
|
mm Wave Ka-Band Receiver |
| 539 |
0776 : 2006 Reaffirmed 2018
|
mm - Wave Variable Attenuator |
| 540 |
0507 2019 (Third Revision)
|
painting of 'B' Vehicles |
| 541 |
0462-01-2018 Third Rev
|
Copper: Wire, Bars, Rods, Tubes, Plates, Sheets And Foils |
| 542 |
0457-01 (Pt 1)-2018 Third Rev
|
Treatments For Protection Of Metals Parts Of Services Store And Equipment Against Corrosion Part 1 Temporary Protection |
| 543 |
0683 : 2018 (First Revision)
|
Fabrication of Composite Part for Aircraft |
| 544 |
0514:2019 (Second Revison)
|
Evaluation Performance of Starter Motor |
| 545 |
0510:2018 (Second Revision)
|
Use of Commercially of the Shelf (Cots) Vehicular Components in Defence Supplies |
| 546 |
0509:2018 (Second Revision)
|
Selection of Material & Quality Assurance for Seat Cushion |
| 547 |
0506: 2019 (Third Revision)
|
Testing and Quality Assurance of Bearings |
| 548 |
0159 : 2011 (Revision No.1)
|
Thermal Imaging Sight |
| 549 |
0521: 2017
|
Evalution and Test Methodology For B-Vehicles |
| 550 |
0165 :2012 (Reaffirmed 2018)
|
High Resolution Picture Transmission Receiving System |
